Aussie CCTV Cams
Full-colour night vision CCTV camera mounted on a Sydney brick home, capturing colour rendering at night over a softly lit driveway

Colour Night CCTV Footage Guide: Fixes for Australia Homes

7 min read · Published 7 Oct 2026 · By the Aussie CCTV team

Your CCTV goes black and white at night because infrared mode replaces visible light — but sensor size, aperture, settings and lighting determine whether you keep genuine colour night CCTV footage.

Key Takeaways

  • Cameras switch to infrared below a light threshold, rendering monochrome night CCTV footage by design.
  • A 1/1.8-inch sensor with an F1.0 aperture gathers far more light than cheap 1/3-inch DIY kits.
  • Lowering the day/night switchover threshold is a free fix that keeps colour mode past dusk.
  • Full-colour cameras like Hikvision ColorVu cost roughly $550–$800 installed per camera in NSW.
  • Mounting cameras at 2.4–3 metres avoids glare and captures identifiable faces after dark.
  • Licensed installers in NSW and SA can test light levels on-site before any upgrade spend.

What Colour Rendering Means in a Security Camera

If your CCTV looks sharp and colourful by day but turns into a flat grey smear after dark, your camera has switched into infrared mode and is recording without visible-spectrum light. The good news: with the right sensor, aperture, settings and ambient lighting, genuine colour night CCTV footage is achievable on almost any property in Australia.

The good news is that most of these problems are fixable — sometimes without spending anything at all. Adjusting day/night thresholds, enabling wide dynamic range, cleaning the lens, adding a warm-white light near the camera zone, or upgrading just your key identification points to full-colour hardware like Hikvision ColorVu can transform night footage from useless to evidentiary-grade. This guide walks through each cause and each fix in plain language, so you can work out exactly what is going wrong on your property.

How Sensor Size and Aperture Affect Night Vision

Colour rendering describes how faithfully a camera reproduces the colours of a scene compared with what your own eye would see. In daylight, even inexpensive cameras manage this reasonably well because there is plenty of light to work with. After dark, everything changes: the camera's ability to hold accurate colour depends on three factors working together — the size of its image sensor, the aperture of its lens, and whatever supplementary lighting is available.

Why Your Camera Goes Black and White at Night

Marketing loves megapixels, but after sunset they are close to meaningless without light-gathering ability behind them. A large sensor collects more photons across its surface. A 1/1.8-inch sensor pulls in dramatically more light than the 1/3-inch sensors fitted to cheap DIY kits, which means more signal and less noise in dim conditions.

Aperture matters just as much. An F1.0 lens lets through roughly four times the light of an F2.0 lens found on budget cameras. Combine a big sensor with a wide aperture and the camera can keep producing genuine colour long after smaller-sensored units have given up and flipped to monochrome.

This combination is precisely the engineering behind Hikvision ColorVu and Dahua Full-Colour cameras. Rather than abandoning colour when light drops, they use large sensors, super-wide apertures and a gentle warm-white supplement LED to capture true full-colour footage around the clock. Uniview's ColorHunter range takes the same approach. In practical terms, that means clothing colours, vehicle colours and hair colours stay visible — often the exact details that identify an offender or settle a dispute. Our installers are fully licensed under state [[poe-vs-wi-fi-cameras-which-is-better-for-australian-homes|security]] laws and comply with the Privacy Act 1988 at every job.

Can Overexposure and Glare Wash Out Colour Footage

Standard security cameras handle darkness with [[how-to-position-cameras-to-avoid-infrared-bounce-back-at-night|infrared]] LEDs. As light levels fall below a set threshold, the camera disengages its IR cut filter and bathes the scene in invisible infrared illumination. Because the sensor no longer receives visible-spectrum colour information, the footage renders in black and white.

That switch alone would be acceptable if the result were clean monochrome video. Unfortunately, IR light reflects off everything — walls, eaves, soffits, spider webs, even raindrops — and bounces straight back into the lens. The frame blows out, contrast collapses, and you end up with washed-out grey footage rather than crisp black-and-white imagery. This double problem, monochrome plus overexposure, is what most people mean when they complain their night vision 'looks terrible'.

Which Technology Wins: Infrared vs Starlight vs Full-Colour

Even in colour mode, placement can wreck your footage. A camera positioned next to a floodlight, under a downlight, or facing a streetlight will expose for the brightest point in the scene. Everything outside that hotspot sinks into murk, faces become featureless white blobs, and number plates glare out completely unreadable.

Reflective surfaces compound the issue. A Colorbond fence, glossy garage door or wet driveway can bounce light directly into the lens. Wide dynamic range (WDR) and highlight compensation features help the sensor balance these extremes, but no setting fully rescues a camera pointed at a light source — repositioning is usually the real answer.

Are These Installation Mistakes Destroying Night-Time Colour

Not every camera position needs premium full-colour hardware, so understanding the trade-offs helps you spend where it counts. Standard infrared remains perfectly adequate for perimeter detection — knowing something moved is enough at the back fence. Starlight or low-light sensors hold partial colour in moderately lit streets and yards. Full-colour cameras deliver identification-grade footage at entries, driveways and anywhere a face or plate matters.

For most Sydney homes and small businesses, a hybrid design wins: full-colour cameras covering the front door, driveway and side gate, with standard IR or smart-detection models handling the backyard and boundaries. You get identification where it matters and sensible coverage everywhere else, without paying full-colour prices for every position.

Should You Try Free Settings Fixes First

A surprising share of the washed-out footage we diagnose comes from installations where the hardware is perfectly fine but the mounting decisions undo it. These are the [[7-common-diy-cctv-installation-mistakes-and-how-professionals-avoid-them|mistakes]] we see most often:

  • Mounting directly beside or beneath floodlights and downlights, causing permanent overexposure
  • Installing above 3.5 metres, capturing crowns of heads instead of faces and spreading available light too thin
  • Infrared reflecting off nearby walls, eaves, cobwebs or rain, washing out the entire frame
  • Salt film and dust on the lens diffusing light — a chronic issue for coastal suburbs
  • Leaving factory-default settings untouched instead of tuning them for the actual scene

Do Cheap Lighting Upgrades Beat Camera Replacement

Before spending a cent on new equipment, log into your recorder or camera interface and check the day/night settings. Many cameras sit on 'auto' with a switchover threshold that flips to infrared far too early in the evening. Lowering that threshold keeps the camera in colour mode well past dusk.

Next, enable WDR if your scene mixes bright lights with deep shadow, and look for highlight compensation options — Hikvision's HLC, for example, is designed specifically to tame number-plate glare and harsh downlights. On standard IR cameras, reducing IR intensity stops close-range washout caused by light bouncing off nearby surfaces.

One more zero-cost step: clean the lens. Dust, salt spray and spider webs scatter infrared light into a fog across the whole image. Coastal properties benefit enormously from a gentle microfibre wipe every few months.

Is Upgrading to Full-Colour Cameras Worth the Cost

If settings tweaks are not enough, add light before replacing hardware. A warm-white LED downlight or sensor-activated light near the camera zone gives even mid-range cameras enough illumination to hold colour through the evening. It costs a fraction of a new camera and frequently outperforms one.

Warm-white matters here — cool blue-white light renders skin tones poorly and can trigger some sensors oddly, while soft warm light keeps colour natural and flattering for identification purposes.

When Upgrading to Full-Colour Cameras Is Worth It

If your system is five or six years old, sensor technology has leapt forward since installation. A modern 4MP ColorVu camera will beat an older 8MP unit at night every time, because resolution without light-gathering ability delivers nothing usable after dark.

Prioritise upgrades at identification points first: front entry, driveway, side access, and any commercial counter or till area. Detection-only zones such as rear fences can retain older cameras longer. If your recorder is ageing as well, a modern NVR adds AcuSense-style person and vehicle detection, which pairs beautifully with full-colour footage for fast, accurate event searching.

Every property brings different challenges — bushfire-zone homes, coastal addresses and rural sites running on 4G all have unique lighting conditions. A proper assessment looks at each camera position's light levels, purpose and mounting options before recommending whether you need new hardware, better placement, or simply correct configuration of what you already own.

Getting Professional Help in NSW

Diagnosing night-footage problems remotely is possible, but a licensed installer can measure actual light levels, test settings on-site and show you side-by-side comparisons before you commit to anything. Look for installers who offer free, no-obligation assessments and honest advice — including telling you when a $20 light bulb beats a $700 camera. Professional installation also ensures cabling, mounting heights and recorder configuration are done correctly the first time, with training at handover so you know how to use every feature your system offers.

Night Vision Technologies Compared

Feature Standard Infrared (IR) Starlight / Low-Light Full-Colour (ColorVu, Full-Colour, ColorHunter)
Footage at night Black and white Colour in moderate low light Full colour 24/7
Typical sensor size 1/3-inch 1/2.8-inch 1/1.8-inch or larger
Lens aperture F2.0 – F2.8 F1.6 F1.0 – F1.2
Light source Invisible IR LEDs Ambient light only Warm-white supplement LED
Effective range 20–30 metres 15–25 metres 20–40 metres
Colour detail (clothing, vehicles) None Partial Excellent
Best use case Perimeter detection Well-lit streets and yards Entries, driveways, identification points
Indicative installed cost per camera $350–$500 $450–$650 $550–$800

Frequently asked questions

Why does my CCTV turn black and white at night in Newcastle NSW?

When light drops below a preset threshold, the camera disengages its IR cut filter and infrared LEDs take over, which the sensor can only render in monochrome. Many homes around Newcastle NSW have this threshold set too aggressively, flipping to infrared well before full darkness. Lowering the switchover point or upgrading to a full-colour model restores genuine colour.

Can I get colour night CCTV footage without floodlights in Adelaide SA?

Yes. Full-colour cameras such as Hikvision ColorVu, Dahua Full-Colour and Uniview ColorHunter pair large sensors with F1.0 apertures and a soft built-in warm-white light, capturing real colour in near-darkness. They suit Adelaide SA properties where harsh floodlighting would annoy neighbours or wash out plates and faces.

How much does a full-colour CCTV upgrade cost in Australia?

Professionally installed full-colour cameras typically run $550–$800 per camera in NSW depending on cabling, mounting height and recorder compatibility. Existing systems can often be mixed with new full-colour units to spread costs, and reputable installers offer free quotes before any commitment.

Do more megapixels improve low-light security camera performance?

No. After dark, sensor size and lens aperture matter far more than resolution. A 4MP camera with a 1/1.8-inch sensor and F1.0 lens dramatically outperforms an older 8MP unit fitted with a small 1/3-inch sensor, because light-gathering ability — not pixel count — determines usable night detail.

Why do faces and number plates appear as white blobs at night?

That is overexposure from infrared reflection or a nearby light source. Reduce IR intensity, enable WDR and HLC settings, reposition the camera away from streetlights and reflective surfaces, and lower mounting height to roughly 2.4–3 metres so faces sit within the correctly exposed zone of the frame.

Will cleaning my camera lens really sharpen night footage?

Yes. Dust, salt film and spider webs diffuse infrared light and wash out the entire frame — a common issue in coastal suburbs like Merewether or Glenelg. A gentle microfibre clean every few months noticeably improves clarity and costs nothing, making it the first step before any hardware spend.

What mounting height best preserves colour detail after dark?

Around 2.4 to 3 metres, angled slightly downward. Cameras mounted at four or five metres capture the tops of heads rather than faces, and the wider field of view spreads available light too thin for reliable colour rendering. Correct height also reduces glare from ground-level reflections.

Is professional installation required under Australian security licensing rules?

In NSW, CCTV installation involving cabling and electrical work must be performed by a licensed installer under AS/NZS standards, and South Australia has equivalent licensing requirements through CBS. Using a licensed technician ensures compliant cabling, correct recorder configuration and handover training so you can adjust day/night settings yourself.

Get a free on-site quote

Licensed installers across Newcastle, the Hunter Region and Adelaide. Fixed written quotes, no hidden fees, no pressure.

Call 02 40 033 972 Request a quote